Aller au contenu
AIHFABS Announces Major Updates to Solutions and Materials Pages and Introduces B2B Project See More +

Matériaux de coulée sous vide : résines PU

Le silicone constitue le moule. La pièce reproduite est normalement en résine polyuréthane (PU), formulée pour approcher certaines propriétés de plastiques techniques ou d’élastomères.

Choose a casting material family

Rigid & semi-rigid PU resins

Start here for housings, panels, clear covers and assembly prototypes. Compare ABS-like, PC-like, PP-like and specialist PU formulations by the behavior your prototype must demonstrate.

Explore PU / ABS-like / PC-like →

Rubber-like & elastomer resins

Start here for grips, flexible boots, cushioning and seal evaluation. Define hardness, deformation and recovery together with tear, compression and exposure requirements.

Explore rubber-like / elastomer →

Matériaux de coulée sous vide : résines PU

Le silicone constitue le moule. La pièce reproduite est normalement en résine polyuréthane (PU), formulée pour approcher certaines propriétés de plastiques techniques ou d’élastomères.

Ces familles de résines sont des pistes de discussion, pas une promesse de disponibilité de chaque formulation. Confirmer la fiche technique exacte et les échantillons avant commande.

Matériau / nuanceApplication typiqueÀ confirmer avant devis
ABS-like →Boîtiers, panneaux et prototypes structurelsComparer résistance, rigidité, choc et vieillissement à la nuance cible exacte.
PC-like →Prototypes transparents et d’évaluation aux chocsValider transparence, couleur, surface et vieillissement sur échantillon.
PMMA (Acrylic)-like →Fenêtres, capots lumineux et modèles visuels de guides de lumièreValider transparence, couleur, surface et vieillissement sur échantillon.
PP-like →Clips, charnières et prototypes souplesPréciser échelle Shore, dureté visée et flexions répétées.
POM-like →Évaluation d’engrenages et d’interfaces d’usureComparer résistance, rigidité, choc et vieillissement à la nuance cible exacte.
PA-like / filled PU →Prototypes structurels chargés ; confirmer le système chargéComparer résistance, rigidité, choc et vieillissement à la nuance cible exacte.
Rubber-like (Elastomer) →Prototypes de joints, poignées et amortisseurs à évaluerPréciser échelle Shore, dureté visée et flexions répétées.
Heat-resistant PU →Prototypes exposés à la chaleur après étude du gradeConfirmer fiche technique, température et durée d’exposition.
Flame-retardant PU →Prototypes de boîtiers électroniques avec exigences feu documentéesDemander les documents UL 94 propres au grade et à l’épaisseur.
Transparent PU →Maquettes visuelles et d’assemblage transparentes ou teintéesValider transparence, couleur, surface et vieillissement sur échantillon.

À confirmer avant devis

Quelle est la température maximale d’utilisation ?

Indiquez température continue, pics, durée d’exposition et cycles de four ou de refusion. La HDT est un résultat d’essai, pas une température continue garantie.

Propriétés proches ne signifie pas matériaux identiques

Les résines de type ABS ou PC sont des systèmes PU, pas de l’ABS ou du PC injecté. Comparez les propriétés nécessaires ; aucun pourcentage universel d’équivalence ne s’applique.

La dureté dépend du grade

Utilisez la valeur Shore A ou Shore D et la méthode d’essai de la résine choisie. La dureté ne démontre ni tenue thermique, ni durée de vie en fatigue, ni compatibilité chimique.

Les grades ignifuges exigent des preuves

Une mention UL 94 V-0 doit correspondre à la résine exacte, à l’épaisseur de l’éprouvette et à l’essai ou à la reconnaissance documentés. Le nom de famille ne constitue pas un classement.

Les pièces souples ne sont pas exclusives à la coulée

Un PU de type caoutchouc peut servir à évaluer des prototypes souples et des joints. L’impression 3D flexible et d’autres moulages existent aussi ; choisissez selon la fonction et la validation.

Select by the job your prototype must do

Choose the test first, then shortlist a resin. A cosmetic model, a loaded enclosure and a compressed seal need different evidence even when their CAD geometry is similar.

Prototype requirementFamilies to reviewEvaluate on the finished part
Enclosures & assembly fitABS-like or rigid PUBosses, screw engagement, mating clearances, stiffness and impact at the intended use temperature.
Clear windows & visual coversTransparent, PC-like or PMMA-like PUHaze, tint, viewing thickness, visible-face polish and appearance after the intended exposure. A clear sample does not establish optical-grade performance.
Clips & repeated flexPP-like or a compliant PU formulationDeflection, recovery and cracking over the required assembly cycles. Review the clip geometry and test the actual mating part.
Grips, boots & cushioningRubber-like elastomer PUShore scale and hardness, tear around thin sections, grip texture, deformation and recovery under load.
Seals & fluid contactElastomer formulation selected for the mediumCompression, leakage, swelling and recovery after exposure to the actual fluid and temperature. Hardness alone cannot establish sealing suitability.
Heat or flame requirementsDocumented specialist PU gradeExact grade, specimen thickness and relevant test conditions. Agree on required reports before ordering.

Appearance, geometry & finishing

Color & surface texture

Identify show faces, target color and gloss level. Supply a physical reference or color standard where appearance matters. Agree whether color is cast into the resin or applied as paint, and review a sample under the intended lighting.

Clear parts

Mark the viewing area and specify what must be visible through it. Master quality, mold surface, part thickness and finishing influence clarity. Discuss bubbles, tint and acceptable visual defects before production.

Walls, undercuts & parting lines

Flag thin walls, deep pockets and fragile projections for mold review. Identify where a parting line or gate witness is acceptable. Silicone tooling can accommodate some undercuts, but demolding still needs to protect both the part and the mold.

Inserts & mating features

Provide the insert specification, location and assembly loads. Identify threads, sealing faces and datum features on a drawing. Review whether a feature should be cast, drilled or finished afterward, including how it will be inspected.

From material shortlist to approved parts

  1. Define the use case

    Send CAD, quantity and a drawing with critical dimensions. Describe loading, temperature, fluids, outdoor exposure and whether the part is for appearance, assembly or functional testing.

  2. Agree on a resin & manufacturing plan

    Review the exact resin designation and data sheet alongside master preparation, mold layout, finish and any inserts. Confirm the proposed delivered condition and material availability in the quotation.

  3. Evaluate the first sample

    Check dimensions, color, surface and assembly. Run representative functional checks on the chosen formulation; compare results against agreed acceptance criteria before releasing the remaining quantity.

  4. Confirm repeat-order requirements

    Record the approved resin, finish and sample reference. Discuss tooling condition and repeat quantity when reordering; mold life and dimensional consistency depend on geometry, resin and handling.

Material selection questions

Is the cast part made of silicone?

The mold is silicone. The parts described here are cast PU resin systems. If your finished component must be silicone, specify that material requirement so a suitable process can be reviewed separately.

Can ABS-like PU replace production ABS?

Use it to evaluate the properties relevant to your prototype. ABS-like describes a performance target rather than identical chemistry. Compare the selected resin with the intended production grade and validate the functions you need.

Can I specify a hardness without selecting a resin?

Provide the target Shore scale and value, but also describe load, deformation, recovery, temperature and contact media. Two formulations with similar hardness can differ in tear resistance, compression behavior and aging.

What dimensional tolerance should I put on my drawing?

Mark critical dimensions, datums and inspection conditions for review. Geometry, master accuracy, resin shrinkage and flexible-part support affect the result. Agree on feature-specific acceptance criteria rather than assuming one tolerance applies to every surface.

What documentation should I request?

Request the exact resin designation and technical data sheet. Specify any material traceability, test report or compliance evidence needed for your application before quotation. A supplier family page or an unrelated printing-material data sheet is not evidence for the delivered casting resin.

Politique de cookies

Nous utilisons des cookies pour personnaliser votre expérience. En utilisant ce site, vous acceptez notre Politique de confidentialité

Accepter